Matala kuormaaja

Fliegl VTS 400 RR

Customized Transport Solution
Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications.

Further Information
Chassis
Steel welded construction
Turntable with robust ball bearing
Foldable rear support
2 wheel chocks + holder
Aluminum side underrun protection
Splash guards at the rear over the entire width
Quarter panel fenders in front of the 1st axle
Excavator arm recess starting above the rear axles to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess on the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm in front of the rear slope
1 storage box recessed in the gooseneck in the floor with a lid, W=720 mm/ L=520 mm / D= 170 mm
1st pair of wheel recesses recessed in the gooseneck in the low-loader wheel well area, sloped for access, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses between the axles recessed in the low-loader in the wheel well area, sloped for access, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in the main beam area is 300 mm higher than the wheel recess.
Wheel recess cover pull-out from the main frame, with wood inserts.
Distance from the outer frame, beam to beam, approx. 1280 mm
Extensions pull-out to 3,000 mm, foldable at the wheel recess extensions (extension not in the rear slope and not in the wheel recesses at the bottom)
Storage compartment for wooden planks in the middle of the loading area or under the loading area, depending on technical feasibility
Wooden planks 70 mm for extension to 3000 mm
Lashing points, low-loader
1 pair of ring lashing points recessed at the front on the gooseneck, each 5 tons
8 pairs of lashing eyes at the top and on the side recessed in the outer frame, each 10 tons
2 x at the front on the gooseneck
6 x in the low-loader, the first lashing point 250 mm from the front and the last one max. 250 mm from the rear, the distance between the lashing points is no more than 1100 mm
5 pairs of ring lashing points recessed in the outer frame, each 5 tons (can be converted to stake pockets)
Lrsdpfx Alji Ri I Negen
Coupling system, trailer, turntable
Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye
Axles + Suspension
SAF drum brake axles
Axle/chassis laser-aligned, reducing tire wear and fuel consumption
Air suspension with lifting and lowering valve, can be operated separately at the front and rear
Wheels and tires
235/75R17.5 according to manufacturer's choice
Steel rims in twin arrangement, factory silver
Braking system
2-line compressed air brake system
Spring-loaded parking brake
Trailer Info Center for displaying vehicle data such as axle load (no calibrated scale) and odometer
Axle load detection via EBS-CAN bus signal, for display on the display in the cab, truck must be suitably prepared, no truck installation (no calibrated scale)
Vehicle-driving stability system
Duomatic connection at the front, with connecting cable to the towing vehicle
EBS, Electronic Braking System with EBS plug at the front, with connecting cable
Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS!
Electrical system
24 Volt, multi-chamber lights in LED with resistor, yellow LED lighting on the side, license plat

Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.